Nord User Forum

Nordish wrote:

Mr_-G- wrote:Do you have several midi channels ON? I.e. you can sometimes send a global and another one (at least in the NS2).
Use a MIDI Monitor to see what is coming out of your MIDI out that might be clogging the U220 buffer.

How should I do that during a gig? Any ideas? I am open to suggestions

I would suppose that it is not a "gig-thing" and whatever you do to fill the U220's buffer *could* be replicated at another time?
Did you check about the MIDI channels?
Did you get a MIDI monitor program and tried to play what you were doing when it happened?

At home i couldn't replicated the Problem. It's not just a gig thing I think.
The Midi Channels are ok
No I haven't

I am now in contact with the nord support. Really nicely! I will send my Global / Panel Parameters and they will check this and they will try it to fix it. Mega Support! Such a direct wire is sought in vain with other manufacturers. Sorry, my bad english!

A new bug (OS 1.26)?

Yesterday I had an issue where B panel synth’s delay or reverb adjustments did not have effect. In other words if I turned for example reverb amount dial I could see parameter value change but it did not realize in sound. But if I saved program and went to another progran and back, then I could hear the difference. Strangely I haven’t come across with this issue earlier and I begin to think that could it be a new bug with OS 1.26.? I will report this to Clavia.

P.S. I can also confirm this another bug of phaser being audible even when it’s set to 0.

EDIT: This bug has been reported to Clavia and I put it also on the bug sheet. They could re-produce it and will try to fix it asap.

My NS3C crashed today when I connected it to my laptop. It deleted most of my programs, and the programs that were still there were in a different order. Has anyone had this before? Almost all the synth presets are gone too. I have to factory reset everything and start over, which is a little disappointing after 3 months of programming.

Ecaroh wrote:A new bug (OS 1.26)?

Yesterday I had an issue where B panel synth’s delay or reverb adjustments did not have effect. In other words if I turned for example reverb amount dial I could see parameter value change but it did not realize in sound. But if I saved program and went to another progran and back, then I could hear the difference. Strangely I haven’t come across with this issue earlier and I begin to think that could it be a new bug with OS 1.26.? I will report this to Clavia.

I've also been experiencing this exact bug.

Dr Kananga wrote:

Ecaroh wrote:A new bug (OS 1.26)?

Yesterday I had an issue where B panel synth’s delay or reverb adjustments did not have effect. In other words if I turned for example reverb amount dial I could see parameter value change but it did not realize in sound. But if I saved program and went to another progran and back, then I could hear the difference. Strangely I haven’t come across with this issue earlier and I begin to think that could it be a new bug with OS 1.26.? I will report this to Clavia.

I've also been experiencing this exact bug.

There'll fix with new OS soon... Don't ask how I know this

luukvk wrote:My NS3C crashed today when I connected it to my laptop. It deleted most of my programs, and the programs that were still there were in a different order. Has anyone had this before? Almost all the synth presets are gone too. I have to factory reset everything and start over, which is a little disappointing after 3 months of programming.

I had something similar happen this weekend although it was not connected to my computer when it happened. I have an NS3 HP76. I booted it up and most of my programs were unavailable with an "Unknown Error" message. The ones that were there were out of order. I did have a backup and I tried to restore from my backup and it crashed during the restore. Now it hangs about 1/3 of the way through the boot sequence and will not boot. I have a ticket in with Nord Support. Did you ever get a resolution or reason for your problem?

What version of code?

-dj

DJKeys wrote:What version of code?

-dj

If you are asking me, it is 1.22.