Nord User Forum

Its just good to have that information in these reports so we can see if certain issues can be directly related to specific OS versions, thanks!

-dj

Hi hope someone can help with this.
Just bought a triple pedal for my NS3 to catch and hold some pads but annoyingly it wont hold the organ (synth + piano engines are caught and held ok). The sustain pedal holds the organ perfectly!!! So why doesn't the sostenuto do the same???

Is the Sustain switched on in the organ section?

Is the sustenuto function working on pianos?

Hi, have you noticed any improvements with the 1.36 update? I still have the following problems:
1- if I use slot B in dual kB mode, the swell pedal does not work, it does not send midi parameters to the connected keyboard and destined to slot B, if I play the organ section directly on the NS 3, the Shell pedal works correctly. Pedal CTRL (EXpression) does not work, either in dual KB or directly on NS3.
2- Problem of MIDI controls: MIDI CC 11 Ctrl Pedal (expression) and all effects controls from MIDI CC from 82 to MIDI CC 119 (enable 1, type eff1, source eff.1, quantity eff.1, eff.1 rate, eff 2 Type, etc. .. etc. .. etc. Do not work, NS3 does not receive the midi controls assigned by the midi keyboard in which it is connected?

My 6th end 8th drawbar stuck in the ''1'' position on my Compact 3. I put drawbars to the end, but I hear that one position out, and see on the display number 1. so, if I want classic 888000000 position, I cannot. Just 888001010... anybody with same problem? Software bug or???

maurich wrote:My 6th end 8th drawbar stuck in the ''1'' position on my Compact 3. I put drawbars to the end, but I hear that one position out, and see on the display number 1. so, if I want classic 888000000 position, I cannot. Just 888001010... anybody with same problem? Software bug or???

Sounds more like a hardware issue to me than anything software related. I'm not sure if there is a "recalibration" procedure for the sliders, but it's probably a good idea to call back to your dealer to check what's up with the drawbars.

Do you have any organs saved with a preset of xxxxx0000? If so, when you load then up, do they stay at 0 until you start moving/touching the drawbars?

baekgaard wrote:

maurich wrote:My 6th end 8th drawbar stuck in the ''1'' position on my Compact 3. I put drawbars to the end, but I hear that one position out, and see on the display number 1. so, if I want classic 888000000 position, I cannot. Just 888001010... anybody with same problem? Software bug or???

Sounds more like a hardware issue to me than anything software related. I'm not sure if there is a "recalibration" procedure for the sliders, but it's probably a good idea to call back to your dealer to check what's up with the drawbars.

Do you have any organs saved with a preset of xxxxx0000? If so, when you load then up, do they stay at 0 until you start moving/touching the drawbars?

Yes, i try this solution. When i move my drawbars, it stucks on 1. I think IT IS hardware issue. Do you have some advice how to recalibrate that?

maurich wrote:My 6th end 8th drawbar stuck in the ''1'' position on my Compact 3. I put drawbars to the end, but I hear that one position out, and see on the display number 1. so, if I want classic 888000000 position, I cannot. Just 888001010... anybody with same problem? Software bug or???

I recently ran into a situation like this which is just possibly (and hopefully) what is happening to you.

In my case, there was a morph assigned to the drawbar settings which was preventing them from behaving entirely normally. I cleared all the morphs and my drawbars stopped misbehaving.

fREDkeys wrote:

maurich wrote:My 6th end 8th drawbar stuck in the ''1'' position on my Compact 3. I put drawbars to the end, but I hear that one position out, and see on the display number 1. so, if I want classic 888000000 position, I cannot. Just 888001010... anybody with same problem? Software bug or???

I recently ran into a situation like this which is just possibly (and hopefully) what is happening to you.

In my case, there was a morph assigned to the drawbar settings which was preventing them from behaving entirely normally. I cleared all the morphs and my drawbars stopped misbehaving.

Unoftunatelly, this is not my case...I'm gonna do factory reset, this is last step of hope...