NS4.
I think this is a bug... When I have a 2 synth layers switched on and using KBD HOLD, if I turn one layer off then that layer continues to sound. I can turn either layer off / on and both layers will sound until I turn both layers off.
With the layers off, KBD HOLD is still 'holding' the sound although you can't hear it until you turn one of the layers back on... at which point you can hear BOTH layers again.
Surely turning off a layer should stop it sounding, even with KBD HOLD turned on? You shouldn't have to turn off ALL layers to get a single layer to stop sounding...?
Bug? Layers sound when turned off if using KBD HOLD
-
maxpiano
- Patch Creator
- Posts: 6805
- Joined: 27 Jun 2011, 13:29
- 13
- Your Nord Gear #1: Nord Stage 3
- Location: Italy
- Has thanked: 502 times
- Been thanked: 2385 times
Re: Bug? Layers sound when turned off if using KBD HOLD
KB HOLD technically is just holding the key(s) not the sound, have you tried to do the same (switch off 1 layer only of the 2 being active) while keeping a key held manually, without using KB HOLD? Just to see if behaviour is the same or specific to KB HOLD being engaged.
-
spradders
- Patch Creator
- Posts: 382
- Joined: 31 Mar 2014, 14:34
- 10
- Your Nord Gear #1: Nord Stage 4
- Has thanked: 140 times
- Been thanked: 133 times
Re: Bug? Layers sound when turned off if using KBD HOLD
Yep the behaviour is the same... if you hold a key (using fingers or KBD HOLD) then the section is still audible even when turned off... until all sections are off, at which point the sound stops.
A bug, surely?
A bug, surely?
-
cgrafx
- Posts: 993
- Joined: 22 Aug 2015, 08:48
- 9
- Your Nord Gear #1: Nord Electro 5
- Your Nord Gear #2: Nord Stage 3
- Location: Northern California
- Has thanked: 3 times
- Been thanked: 330 times
- Contact:
Re: Bug? Layers sound when turned off if using KBD HOLD
or not, as that would be a part of what makes seamless transitions work. As long as a key is being pressed, it continues to sound even when a program change has occurred and the program your switching to could easily have the section turned off. you wouldn't want the sound to stop in the middle would you?
- These users thanked the author cgrafx for the post (total 3):
- maxpiano, FZiegler, WannitBBBad
Current Gear: NS3C, NP5-88, NP5-73, Alesis QS7.1 & QS8.2, Hammond B3 with Leslie 122, Yamaha CP70, Yamaha C3 6' Grand, Roland D-05, Roland AX-Edge
-
spradders
- Patch Creator
- Posts: 382
- Joined: 31 Mar 2014, 14:34
- 10
- Your Nord Gear #1: Nord Stage 4
- Has thanked: 140 times
- Been thanked: 133 times
Re: Bug? Layers sound when turned off if using KBD HOLD
Hmm, I agree when changing program. But if I'm staying on the same program and turning a layer off, I expect the sound to stop.
-
missoundscape
- Patch Creator
- Posts: 101
- Joined: 14 Jun 2016, 10:02
- 8
- Your Nord Gear #1: Nord Stage 4
- Your Nord Gear #2: Nord Wave 2
- Has thanked: 64 times
- Been thanked: 83 times
- Contact:
Re: Bug? Layers sound when turned off if using KBD HOLD
This works the same as on the Nord Wave 2. It can be used in certain use cases.
I use it to keep a note/chord sustained/arp (or droning) with KBhold, turn the layer off and playing on the other layers.
I used it here viewtopic.php?t=19394, to keep an arp going.
I use it to keep a note/chord sustained/arp (or droning) with KBhold, turn the layer off and playing on the other layers.
I used it here viewtopic.php?t=19394, to keep an arp going.